DIY Projects

Mason Jar Soap Dispenser DIY (No Drill Needed)

Make a mason jar soap dispenser in about 15 minutes with a pump-lid kit, or use a hammer-and-nail lid (add sealant cure time). Leak-proofing tips included.

In this guide
  1. At a glance
  2. What you'll need
  3. Pick the right jar and lid size
  4. How to make a mason jar soap dispenser: two ways to do the lid
  5. Route A: use a pump-lid kit (easiest, no tools)
  6. Route B: reuse a pump with a hammer and nail
  7. Stop leaks
  8. A renter-friendly finish
  9. Refilling and keeping it clean
  10. Frequently asked questions
  11. Do I need a drill to make a mason jar soap dispenser?
  12. Can I use any soap in a mason jar dispenser?
  13. How do I stop my mason jar soap dispenser from leaking?
  14. Do I need to clean the dispenser before refilling it?
  15. Sources

A mason jar soap dispenser is one of the cheapest bathroom and kitchen upgrades you can make: a pump on a jar lid. This guide shows two ways to make one: a no-tools pump-lid kit that takes about 15 minutes, and a budget version that reuses a pump you already have with just a hammer and nail (allow extra time for the sealant to cure). It also covers how to stop leaks and keep the dispenser hygienic.

At a glance

  • Time: about 15 minutes for the pump-lid kit (Route A). The budget route (Route B) takes a little longer, plus the sealant's cure time from its label before you can fill the jar
  • Difficulty: easy
  • Approximate cost: about $0 to $12 depending on the route you pick (prices vary by store and region)
  • Tools: none for the pump-lid kit; a hammer, a nail and scrap wood for the budget route
  • Good for renters: it sits on a counter, so there is nothing to mount, drill into a wall or glue down

What you'll need

For either route

  • 1 mason jar (regular or wide mouth), with no chips or cracks
  • Liquid hand soap
  • A small tray or saucer to stand the jar on (optional, but it catches drips)

Route A: pump-lid kit (no tools)

  • A mason jar pump lid made for your jar size. Check the package for "regular mouth" or "wide mouth".

Route B: reuse a pump (budget)

  • A two-piece canning lid set (flat lid plus screw band) that fits your jar. You only use these as soap-dispenser parts from now on.
  • A working liquid-soap pump from an empty hand soap bottle, washed out
  • Hammer and 1 or 2 nails (a thin one to start, a thicker one to widen the hole)
  • A piece of scrap wood to hammer onto
  • Safety glasses and work gloves
  • A marker, scissors and an adhesive or sealant made for bonding metal and plastic (optional but recommended for leak-proofing)

Safety: If you plan to hammer a lid, safety glasses with side protection are not optional. OSHA's workplace rule requires eye protection with side protection where there is a flying-object hazard, and it points to the ANSI Z87.1 standard for eyewear.

Pick the right jar and lid size

Mason jars come with two standard openings. The standard (regular) mouth is about 2-3/8 inches (roughly 60 mm) across, and wide-mouth jars are about 3 inches (roughly 76 mm), according to the National Center for Home Food Preservation. Lids and bands are sold for one size or the other, so match your pump lid or lid set to your jar before you buy.

Run a finger around the rim of the jar before you start. The National Center for Home Food Preservation advises examining jars before use, because even small scratches can lead to cracking. For this project the same check keeps you safe: a chipped rim can cut you, so pick a different jar if you find a nick or crack.

How to make a mason jar soap dispenser: two ways to do the lid

Route A: use a pump-lid kit (easiest, no tools)

  1. Wash and dry the jar.
  2. Check that the kit's dip tube is not longer than the jar is tall. If it is, trim the tube with scissors so it stops about half an inch above the bottom.
  3. Fill the jar with liquid soap, leaving a gap at the top so the pump does not overflow when you screw it in.
  4. Screw the pump lid on until it is snug. Press the pump a few times to prime it.

That is the whole project. Pick this route for the least fuss.

Route B: reuse a pump with a hammer and nail

Pump designs differ, so test the hole size against your pump. Start with a small hole and enlarge it in steps: a hole that is too big cannot be fixed.

Safety: Punching metal leaves sharp edges and burrs. Wear safety glasses and work gloves, keep your fingers away from the nail, and hammer onto scrap wood on a stable surface. Flatten or file down any sharp metal on the finished hole before you handle the lid without gloves.

Step 1: Measure the pump

Hold the pump over the flat metal lid. The hole needs to be big enough for the narrow body of the pump (the part below the collar) to pass through, while the wider collar or flange stays on top of the lid.

Step 2: Mark the center

Place the flat lid on the scrap wood with the sealing-compound side down. Mark the center with a marker.

Step 3: Punch a pilot hole

Hold the nail on the mark and tap it through with the hammer. Use light, steady taps. Remove the nail.

Step 4: Widen the hole a little at a time

Switch to a thicker nail and tap it through again from the same side, then repeat with progressively thicker tools as needed. After each pass, test the pump body against the hole. Stop as soon as the body slides through without force.

Step 5: Smooth the edge

Turn the lid over and check for raised burrs. Gently tap them flat on the scrap wood, or file them smooth, so they do not cut your hands or snag the pump.

Step 6: Fit the pump

Push the pump body and dip tube through the hole from the top, so the collar or flange rests on the lid. Trim the dip tube with scissors so it ends about half an inch above the bottom of the jar once the lid is on.

Step 7: Seal it (leak-proofing)

Lift the pump slightly and run a thin ring of adhesive or sealant made for metal and plastic around the pump body where it meets the lid, then press it back down. Follow the product label for cure time before you add soap, and work in a ventilated space.

Safety: Adhesives and sealants can give off fumes and irritate skin. Read the label and follow its ventilation, glove and cure-time directions.

Step 8: Assemble and fill

Fill the jar with liquid soap, leaving a gap at the top. Set the pump and lid on the jar, put the screw band on, and tighten it by hand. Prime the pump by pressing it several times.

Soap-only lid: do not use a pierced lid for canning food. The sealing compound on canning lids is meant for one canning process only, according to University of Nebraska–Lincoln Extension, and a lid with a hole in it can never seal. Mark it for soap use only.

Stop leaks

If soap seeps out, work through this list in order:

  • Seal at the pump: most leaks start where the pump meets the lid. Re-seat the pump and add a little more sealant, then let it cure per the label.
  • Band tension: tighten the screw band by hand until it is snug, not forced.
  • Gasket: on the two-piece lid, the flat lid's sealing compound faces the jar rim. Make sure it is not folded or dented.
  • Fill level: leave a gap at the top so soap does not push up when you screw the pump in.

A renter-friendly finish

Because the dispenser is freestanding, there is nothing to patch or repair when you move out. To finish it off:

  • Stand it on a small tray, saucer or cut-down coaster so drips do not mark the counter.
  • Write the soap scent on a removable label, so you know what is inside when you refill.

Refilling and keeping it clean

A dispenser you refill at home is not a problem on its own, but do not just top off the jar. A 2011 study in Applied and Environmental Microbiology found bacterial contamination in refillable bulk-soap dispensers at an elementary school, where washing with contaminated soap increased bacteria on hands. The study looked at a school setting, not home use, but it is a good reason to build a simple habit: when the jar is empty, wash it, rinse it and let it dry fully before you refill it.

Then use it as the CDC recommends: wet your hands, apply soap, lather the backs of your hands, between your fingers and under your nails, and scrub for at least 20 seconds.

Frequently asked questions

Do I need a drill to make a mason jar soap dispenser?

No. Route A needs no tools because you swap the lid. Route B uses a hammer and nail to make a hole in a flat canning lid, so you can skip a drill.

Can I use any soap in a mason jar dispenser?

Use liquid hand soap that flows freely. If the pump struggles, try a thinner liquid soap. Foaming hand soap is made for foaming pumps, so use a foaming pump if you want to keep it foamy.

How do I stop my mason jar soap dispenser from leaking?

Seal the pump where it meets the lid, tighten the band by hand, and leave a gap at the top of the jar when you fill it. If it still leaks, re-seat the pump and re-seal, letting the sealant cure according to the label.

Do I need to clean the dispenser before refilling it?

It is a good habit. Use up the soap, wash and rinse the jar, let it dry fully, then refill instead of topping off. The 2011 study above looked at refillable dispensers in a school, not at home, so treat this as sensible hygiene rather than a rule.

Sources

  • #mason jar
  • #soap dispenser
  • #bathroom
  • #budget diy
  • #renter friendly